Network/Ports

Network Overview

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Active Adapter Auto* Standard Network Wireless	Specify how a network is connected. Note: Wireless appears only when a wireless network adapter is installed.
Network Status	Show the connection status of the printer network.
Display Network Status on Printer On* Off	Show the network status on the display.
Speed, Duplex	Show the speed of the currently active network card.
IPv4	Show the IPv4 address.
All IPv6 Addresses	Show all IPv6 addresses.
Reset Print Server	Reset all active network connections to the printer. Note: This setting removes all network configuration settings.
Network Job Timeout Off On* (90 seconds)	Set the time before the printer cancels a network print job.
Banner Page Off* On	Print a banner page.

Menu item

Description

Active Adapter

Auto*
Standard Network
Wireless

Specify how a network is connected.

Note: Wireless appears only when a wireless network adapter is installed.

Network Status

Show the connection status of the printer network.

Display Network Status on Printer

On*
Off

Show the network status on the display.

Speed, Duplex

Show the speed of the currently active network card.

IPv4

Show the IPv4 address.

All IPv6 Addresses

Show all IPv6 addresses.

Reset Print Server

Reset all active network connections to the printer.

Note: This setting removes all network configuration settings.

Network Job Timeout

Off
On* (90 seconds)

Set the time before the printer cancels a network print job.

Banner Page

Off*
On

Print a banner page.

Wireless

Note: This menu is available only in printers connected to a Wi-Fi network or printers that have a wireless network adapter.

Menu item	Description
Setup Using Mobile App	Configure the Wi-Fi connection using Lexmark Mobile Assistant.
Setup On Printer Panel Choose Network Add Wi-Fi Network Network Name Network Mode Infrastructure Wireless Security Mode Disabled* WEP WPA2/WPA - Personal WPA2 - Personal 802.1x - RADIUS	Configure the Wi-Fi connection using the control panel. Note: 802.1x - RADIUS can be configured only from the Embedded Web Server.
Wi-Fi Protected Setup Start Push Button Method Start PIN Method	Establish a Wi-Fi network and enable network security. Notes: Start Push-Button Method connects the printer to a Wi-Fi network when buttons on both the printer and the access point (wireless router) are pressed within a given time. Start PIN Method connects the printer to a Wi-Fi network when a PIN on the printer is entered into the wireless settings of the access point.
Network Mode BSS Type Infrastructure*	Set the network mode.
Enable Wi-Fi Direct On Off*	Enable Wi-Fi Direct-capable devices to connect directly to the printer.
Compatibility 802.11b/g/n (2.4GHz)* 802.11a/b/g/n/ac (2.4GHz/5GHz) 802.11a/n/ac (5GHz)	Specify the standard for the Wi-Fi network. Note: 802.11a/b/g/n/ac (2.4GHz/5GHz) and 802.11a/n/ac (5GHz) only appear when a Wi-Fi option is installed.
Wireless Security Mode Disabled* WEP WPA2/WPA-Personal WPA2-Personal 802.1x - RADIUS	Set the security mode for connecting the printer to Wi-Fi devices. Note: 802.1x - RADIUS can be configured only from the Embedded Web Server.
WEP Authentication Mode Auto* Open Shared	Set the type of Wireless Encryption Protocol (WEP) for the printer. Note: This menu item appears only when the Wireless Security Mode is set to WEP.
Set WEP Key	Specify a WEP password for secure Wi-Fi connection.
WPA2/WPA Personal AES	Enable Wi-Fi security through Wi-Fi Protected Access (WPA). Note: This menu item appears only when the Wireless Security Mode is set to WPA2/WPA-Personal.
Set Pre-Shared Key	Set the password for secure Wi-Fi connection.
WPA2-Personal AES	Enable Wi-Fi security through WPA2. Note: This menu item appears only when the Wireless Security Mode is set to WPA2-Personal.
802.1x Encryption Mode WPA+ WPA2*	Enable Wi-Fi security through 802.1x standard. Notes: This menu item appears only when the Wireless Security Mode is set to 802.1x - RADIUS. 802.1x - RADIUS can be configured only from the Embedded Web Server.
IPv4 Enable DHCP On* Off Set Static IP Address IP Address Netmask Gateway	Enable Dynamic Host Configuration Protocol (DHCP) and configure static IP address. Note: DHCP is a standard protocol that allows a server to distribute IP addressing and configuration information dynamically to clients.
IPv6 Enable IPv6 On* Off Enable DHCPv6 On Off* Stateless Address Autoconfiguration On* Off DNS Server Address Manually Assigned IPv6 Address Manually Assigned IPv6 Router Address Prefix All IPv6 Addresses All IPv6 Router Addresses	Enable and configure IPv6 settings in the printer.
Network Address UAA LAA	View the network addresses.
PCL SmartSwitch Off On*	Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language. Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
PS SmartSwitch Off On*	Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language. Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
Job Buffering On Off*	Temporarily store print jobs in the printer hard disk before printing. Note: This menu item appears only when a hard disk is installed.
Mac Binary PS Auto* On Off	Set the printer to process Macintosh binary PostScript print jobs. Notes: On processes raw binary PostScript print jobs. Off filters print jobs using the standard protocol.

Menu item

Description

Setup Using Mobile App

Configure the Wi-Fi connection using Lexmark Mobile Assistant.

Setup On Printer Panel

Choose Network
Add Wi-Fi Network
Network Name
Network Mode
Infrastructure
Wireless Security Mode
Disabled*
WEP
WPA2/WPA - Personal
WPA2 - Personal
802.1x - RADIUS

Configure the Wi-Fi connection using the control panel.

Note: 802.1x - RADIUS can be configured only from the Embedded Web Server.

Wi-Fi Protected Setup

Start Push Button Method
Start PIN Method

Establish a Wi-Fi network and enable network security.

Notes:

Start Push-Button Method connects the printer to a Wi-Fi network when buttons on both the printer and the access point (wireless router) are pressed within a given time.
Start PIN Method connects the printer to a Wi-Fi network when a PIN on the printer is entered into the wireless settings of the access point.

Network Mode

BSS Type
Infrastructure*

Set the network mode.

Enable Wi-Fi Direct

On
Off*

Enable Wi-Fi Direct-capable devices to connect directly to the printer.

Compatibility

802.11b/g/n (2.4GHz)*
802.11a/b/g/n/ac (2.4GHz/5GHz)
802.11a/n/ac (5GHz)

Specify the standard for the Wi-Fi network.

Note: 802.11a/b/g/n/ac (2.4GHz/5GHz) and 802.11a/n/ac (5GHz) only appear when a Wi-Fi option is installed.

Wireless Security Mode

Disabled*
WEP
WPA2/WPA-Personal
WPA2-Personal
802.1x - RADIUS

Set the security mode for connecting the printer to Wi-Fi devices.

Note: 802.1x - RADIUS can be configured only from the Embedded Web Server.

WEP Authentication Mode

Auto*
Open
Shared

Set the type of Wireless Encryption Protocol (WEP) for the printer.

Note: This menu item appears only when the Wireless Security Mode is set to WEP.

Set WEP Key

Specify a WEP password for secure Wi-Fi connection.

WPA2/WPA Personal

AES

Enable Wi-Fi security through Wi-Fi Protected Access (WPA).

Note: This menu item appears only when the Wireless Security Mode is set to WPA2/WPA-Personal.

Set Pre-Shared Key

Set the password for secure Wi-Fi connection.

WPA2-Personal

AES

Enable Wi-Fi security through WPA2.

Note: This menu item appears only when the Wireless Security Mode is set to WPA2-Personal.

802.1x Encryption Mode

WPA+
WPA2*

Enable Wi-Fi security through 802.1x standard.

Notes:

This menu item appears only when the Wireless Security Mode is set to 802.1x - RADIUS.
802.1x - RADIUS can be configured only from the Embedded Web Server.

IPv4

Enable DHCP
On*
Off
Set Static IP Address
IP Address
Netmask
Gateway

Enable Dynamic Host Configuration Protocol (DHCP) and configure static IP address.

Note: DHCP is a standard protocol that allows a server to distribute IP addressing and configuration information dynamically to clients.

IPv6

Enable IPv6
On*
Off
Enable DHCPv6
On
Off*
Stateless Address Autoconfiguration
On*
Off
DNS Server Address
Manually Assigned IPv6 Address
Manually Assigned IPv6 Router
Address Prefix
All IPv6 Addresses
All IPv6 Router Addresses

Enable and configure IPv6 settings in the printer.

Network Address

UAA
LAA

View the network addresses.

PCL SmartSwitch

Off
On*

Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language.

Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

PS SmartSwitch

Off
On*

Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language.

Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

Job Buffering

On
Off*

Temporarily store print jobs in the printer hard disk before printing.

Note: This menu item appears only when a hard disk is installed.

Mac Binary PS

Auto*
On
Off

Set the printer to process Macintosh binary PostScript print jobs.

Notes:

On processes raw binary PostScript print jobs.
Off filters print jobs using the standard protocol.

Ethernet

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Network Speed	Show the speed of an active network adapter.
IPv4 Enable DHCP On* Off	Enable Dynamic Host Configuration Protocol (DHCP). Note: DHCP is a standard protocol that allows a server to distribute IP addressing and configuration information to clients dynamically.
IPv4 Set Static IP Address IP Address Netmask Gateway	Set the static IP address of your printer.
IPv6 Enable IPv6 Off* On	Enable IPv6 in the printer.
IPv6 Enable DHCPv6 Off* On	Enable DHCPv6 in the printer.
IPv6 Stateless Address Autoconfiguration Off On*	Set the network adapter to accept the automatic IPv6 address configuration entries provided by a router.
IPv6 DNS Server Address	Specify the DNS server address.
IPv6 Manually Assigned IPv6 Address	Assign the IPv6 address.
IPv6 Manually Assigned IPv6 Router	Assign the IPv6 address.
IPv6 Address Prefix 0–128 (64*)	Specify the address prefix.
IPv6 All IPv6 Addresses	Show all IPv6 addresses.
IPv6 All IPv6 Router Addresses	Show all IPv6 router addresses.
Network Address UAA LAA	Show the printer Media Access Control (MAC) addresses: Locally Administered Address (LAA) and Universally Administered Address (UAA). Note: You can change the printer LAA manually.
PCL SmartSwitch Off On*	Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language. Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
PS SmartSwitch Off On*	Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language. Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
Job Buffering Off On*	Temporarily store jobs on the printer hard disk before printing. Notes: This menu item appears only when a hard disk is installed. This menu item appears only in some printer models.
Mac Binary PS Auto* On Off	Set the printer to process Macintosh binary PostScript print jobs. Notes: On processes raw binary PostScript print jobs. Off filters print jobs using the standard protocol.
Energy Efficient Ethernet Off On*	Reduce power consumption when the printer does not receive data from the Ethernet network.

Menu item

Description

Network Speed

Show the speed of an active network adapter.

IPv4

Enable DHCP
On*
Off

Enable Dynamic Host Configuration Protocol (DHCP).

Note: DHCP is a standard protocol that allows a server to distribute IP addressing and configuration information to clients dynamically.

IPv4

Set Static IP Address
IP Address
Netmask
Gateway

Set the static IP address of your printer.

IPv6

Enable IPv6
Off*
On

Enable IPv6 in the printer.

IPv6

Enable DHCPv6
Off*
On

Enable DHCPv6 in the printer.

IPv6

Stateless Address Autoconfiguration
Off
On*

Set the network adapter to accept the automatic IPv6 address configuration entries provided by a router.

IPv6

DNS Server Address

Specify the DNS server address.

IPv6

Manually Assigned IPv6 Address

Assign the IPv6 address.

IPv6

Manually Assigned IPv6 Router

Assign the IPv6 address.

IPv6

Address Prefix
0–128 (64*)

Specify the address prefix.

IPv6

All IPv6 Addresses

Show all IPv6 addresses.

IPv6

All IPv6 Router Addresses

Show all IPv6 router addresses.

Network Address

UAA
LAA

Show the printer Media Access Control (MAC) addresses: Locally Administered Address (LAA) and Universally Administered Address (UAA).

Note: You can change the printer LAA manually.

PCL SmartSwitch

Off
On*

Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language.

Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

PS SmartSwitch

Off
On*

Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language.

Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

Job Buffering

Off
On*

Temporarily store jobs on the printer hard disk before printing.

Notes:

This menu item appears only when a hard disk is installed.
This menu item appears only in some printer models.

Mac Binary PS

Auto*
On
Off

Set the printer to process Macintosh binary PostScript print jobs.

Notes:

On processes raw binary PostScript print jobs.
Off filters print jobs using the standard protocol.

Energy Efficient Ethernet

Off
On*

Reduce power consumption when the printer does not receive data from the Ethernet network.

TCP/IP

Note: This menu appears only in network printers or printers attached to print servers.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Set Hostname	Set the current TCP/IP host name.
Domain Name	Set the domain name.
Allow DHCP/BOOTP to update NTP server Off On*	Allow the DHCP and BOOTP clients to update the NTP settings of the printer.
Zero Configuration Name	Specify a service name for the zero configuration network.
Enable Auto IP Off* On	Assign an IP address automatically.
DNS Server Address	Specify the current Domain Name System (DNS) server address.
Backup DNS Address	Specify the backup DNS server addresses.
Backup DNS Address 2
Backup DNS Address 3
Domain Search Order	Specify a list of domain names to locate the printer and its resources that reside in different domains on the network.
Enable DDNS Off* On	Update the Dynamic DNS settings.
DDNS TTL 300-31536000 (3600*)	Specify the current DDNS settings.
Default TTL 5-254 (254*)
DDNS Refresh Time 300-31536000 (604800*)
Enable mDNS Off On*	Update multicast DNS settings.
WINS Address	Specify a server address for Windows Internet Name Service (WINS).
Enable BOOTP Off* On	Allow the BOOTP to assign a printer IP address.
Restricted Server List	Specify an IP address for the TCP connections. Notes: Use a comma to separate each IP address. You can add up to 50 IP addresses.
Restricted Server List Options Block All Ports* Block Printing Only Block Printing and HTTP Only	Specify how the IP addresses in the list can access the printer functionality.
MTU 256-1500 (1500*)	Specify a maximum transmission unit (MTU) parameter for the TCP connections.
Raw Print Port 1–65535 (9100*)	Specify a raw port number for printers connected on a network.
Outbound Traffic Maximum Speed Off* On	Enable the printer maximum transfer rate.
Enable SSLv2 Off* On	Enable the SSLv2 protocol.
Enable SSLv3 Off* On	Enable the SSLv3 protocol.
Enable TLSv1.0 Off On*	Enable the TLSv1.0 protocol.
Enable TLSv1.1 Off On*	Enable the TLSv1.1 protocol.
SSL Cipher List	Specify the cipher algorithms to use for the SSL or the TLS connections.

Menu item

Description

Set Hostname

Set the current TCP/IP host name.

Domain Name

Set the domain name.

Allow DHCP/BOOTP to update NTP server

Off
On*

Allow the DHCP and BOOTP clients to update the NTP settings of the printer.

Zero Configuration Name

Specify a service name for the zero configuration network.

Enable Auto IP

Off*
On

Assign an IP address automatically.

DNS Server Address

Specify the current Domain Name System (DNS) server address.

Backup DNS Address

Specify the backup DNS server addresses.

Backup DNS Address 2

Backup DNS Address 3

Domain Search Order

Specify a list of domain names to locate the printer and its resources that reside in different domains on the network.

Enable DDNS

Off*
On

Update the Dynamic DNS settings.

DDNS TTL

300-31536000 (3600*)

Specify the current DDNS settings.

Default TTL

5-254 (254*)

DDNS Refresh Time

300-31536000 (604800*)

Enable mDNS

Off
On*

Update multicast DNS settings.

WINS Address

Specify a server address for Windows Internet Name Service (WINS).

Enable BOOTP

Off*
On

Allow the BOOTP to assign a printer IP address.

Restricted Server List

Specify an IP address for the TCP connections.

Notes:

Use a comma to separate each IP address.
You can add up to 50 IP addresses.

Restricted Server List Options

Block All Ports*
Block Printing Only
Block Printing and HTTP Only

Specify how the IP addresses in the list can access the printer functionality.

MTU

256-1500 (1500*)

Specify a maximum transmission unit (MTU) parameter for the TCP connections.

Raw Print Port

1–65535 (9100*)

Specify a raw port number for printers connected on a network.

Outbound Traffic Maximum Speed

Off*
On

Enable the printer maximum transfer rate.

Enable SSLv2

Off*
On

Enable the SSLv2 protocol.

Enable SSLv3

Off*
On

Enable the SSLv3 protocol.

Enable TLSv1.0

Off
On*

Enable the TLSv1.0 protocol.

Enable TLSv1.1

Off
On*

Enable the TLSv1.1 protocol.

SSL Cipher List

Specify the cipher algorithms to use for the SSL or the TLS connections.

SNMP

Note: This menu appears only in network printers or printers that are attached to print servers.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
SNMP Versions 1 and 2c Enabled Off On* Allow SNMP Set Off On* Enable PPM MIB Off On* SNMP Community	Configure Simple Network Management Protocol (SNMP) versions 1 and 2c to install print drivers and applications.
SNMP Version 3 Enabled Off On* Set Read/Write Credentials User Name Password Set Read-only Credentials User Name Password Authentication Hash MD5 SHA1* Minimum Authentication Level No Authentication, No Privacy Authentication, No Privacy Authentication, Privacy* Privacy Algorithm DES AES-128*	Configure SNMP version 3 to install and update the printer security.

Menu item

Description

SNMP Versions 1 and 2c

Enabled
Off
On*
Allow SNMP Set
Off
On*
Enable PPM MIB
Off
On*
SNMP Community

Configure Simple Network Management Protocol (SNMP) versions 1 and 2c to install print drivers and applications.

SNMP Version 3

Enabled
Off
On*
Set Read/Write Credentials
User Name
Password
Set Read-only Credentials
User Name
Password
Authentication Hash
MD5
SHA1*
Minimum Authentication Level
No Authentication, No Privacy
Authentication, No Privacy
Authentication, Privacy*
Privacy Algorithm
DES
AES-128*

Configure SNMP version 3 to install and update the printer security.

IPSec

Note: This menu appears only in network printers or printers that are attached to print servers.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Enable IPSec Off* On	Enable Internet Protocol Security (IPSec).
Base Configuration Default* Compatibility Secure	Set the IPSec base configuration. Note: This menu item appears only when Enable IPSec is set to On.
DH (Diffie-Hellman) Group Proposal modp2048 (14)* modp3072 (15) modp4096 (16) modp6144 (17)	Set the IPSec encryption. Note: This menu item appears only when Base Configuration is set to Compatibility.
Proposed Encryption Method 3DES AES*	Specify the encryption and authentication methods to connect to a network securely. Note: These menu items appear only when Base Configuration is set to Compatibility.
Proposed Authentication Method SHA1 SHA256* SHA512
IKE SA Lifetime (Hours) 1 2 4 8 24*	Set the amount of time before a new authentication key is generated. Note: These menu items appear only when Base Configuration is set to Secure.
IPSec SA Lifetime (Hours) 1 2 4 8* 24
IPSec Device Certificate	Specify an IPSec certificate. Note: This menu item appears only when Enable IPSec is set to On.
Pre-Shared Key Authenticated Connections Host [x] Address Key	Configure the authenticated connections of the printer. Note: These menu items appear only when Enable IPSec is set to On.
Certificate Authenticated Connections Host [x] Address[/subnet] Address[/subnet]

Menu item

Description

Enable IPSec

Off*
On

Enable Internet Protocol Security (IPSec).

Base Configuration

Default*
Compatibility
Secure

Set the IPSec base configuration.

Note: This menu item appears only when Enable IPSec is set to On.

DH (Diffie-Hellman) Group Proposal

modp2048 (14)*
modp3072 (15)
modp4096 (16)
modp6144 (17)

Set the IPSec encryption.

Note: This menu item appears only when Base Configuration is set to Compatibility.

Proposed Encryption Method

3DES
AES*

Specify the encryption and authentication methods to connect to a network securely.

Note: These menu items appear only when Base Configuration is set to Compatibility.

Proposed Authentication Method

SHA1
SHA256*
SHA512

IKE SA Lifetime (Hours)

1
2
4
8
24*

Set the amount of time before a new authentication key is generated.

Note: These menu items appear only when Base Configuration is set to Secure.

IPSec SA Lifetime (Hours)

1
2
4
8*
24

IPSec Device Certificate

Specify an IPSec certificate.

Note: This menu item appears only when Enable IPSec is set to On.

Pre-Shared Key Authenticated Connections

Host [x]
Address
Key

Configure the authenticated connections of the printer.

Note: These menu items appear only when Enable IPSec is set to On.

Certificate Authenticated Connections

Host [x] Address[/subnet]
Address[/subnet]

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Active Off* On	Let the printer join networks that require authentication before allowing access. Note: To configure the settings of this menu item, access the Embedded Web Server.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
LPD Timeout 0–65535 seconds (90*)	Set the time-out value to stop the Line Printer Daemon (LPD) server from waiting indefinitely for hung or invalid print jobs.
LPD Banner Page Off* On	Print a banner page for all LPD print jobs. Note: A banner page is the first page of a print job used as a separator of print jobs and to identify the originator of the print job request.
LPD Trailer Page Off* On	Print a trailer page for all LPD print jobs. Note: A trailer page is the last page of a print job.
LPD Carriage Return Conversion Off* On	Enable carriage return conversion. Note: Carriage return is a mechanism that commands the printer to move the position of the cursor to the first position on the same line.

HTTP/FTP Settings

Note: This menu appears only in network printers or printers attached to print servers.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Enable HTTP Server Off On*	Access the Embedded Web Server to monitor and manage the printer.
Enable HTTPS Off On*	Configure the Hypertext Transfer Protocol Secure (HTTPS) settings.
Force HTTPS Connections Off* On	Force the printer to use the HTTPS connections.
Enable FTP/TFTP Off On*	Send files using FTP.
Local Domains	Specify domain names for HTTP and FTP servers. Note: This menu item appears only in some printer models.
HTTP Proxy IP Address	Configure the HTTP and FTP server settings. Note: These menu items appear only in some printer models.
FTP Proxy IP Address
HTTP Default IP Port 1–65535 (80*)
HTTPS Device Certificate
FTP Default IP Port 1–65535 (21*)
Timeout for HTTP/FTP Requests 1–299 (30*)	Specify the amount of time before the server connection stops.
Retries for HTTP/FTP Requests 1–299 (3*)	Set the number of retries to connect to the HTTP/FTP server.

Menu item

Description

Enable HTTP Server

Off
On*

Access the Embedded Web Server to monitor and manage the printer.

Enable HTTPS

Off
On*

Configure the Hypertext Transfer Protocol Secure (HTTPS) settings.

Force HTTPS Connections

Off*
On

Force the printer to use the HTTPS connections.

Enable FTP/TFTP

Off
On*

Send files using FTP.

Local Domains

Specify domain names for HTTP and FTP servers.

Note: This menu item appears only in some printer models.

HTTP Proxy IP Address

Configure the HTTP and FTP server settings.

Note: These menu items appear only in some printer models.

FTP Proxy IP Address

HTTP Default IP Port

1–65535 (80*)

HTTPS Device Certificate

FTP Default IP Port

1–65535 (21*)

Timeout for HTTP/FTP Requests

1–299 (30*)

Specify the amount of time before the server connection stops.

Retries for HTTP/FTP Requests

1–299 (3*)

Set the number of retries to connect to the HTTP/FTP server.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Enable ThinPrint Off On*	Print using ThinPrint.
Port Number 4000–4999 (4000*)	Set the port number for the ThinPrint server.
Bandwidth (bits/sec) 100–1000000 (0*)	Set the speed to transmit data in a ThinPrint environment.
Packet Size (kbytes) 0–64000 (0*)	Set the packet size for data transmission.

USB

Note: This menu appears only in some printer models.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
PCL SmartSwitch Off On*	Set the printer to switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language. Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
PS SmartSwitch Off On*	Set the printer to switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language. Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
Job Buffering Off* On	Temporarily store jobs on the printer hard disk before printing. Note: This menu item appears only when a hard disk installed.
Mac Binary PS On Auto* Off	Set the printer to process Macintosh binary PostScript print jobs. Notes: When set to On, the printer processes raw binary PostScript print jobs from computers using the Macintosh operating system. When set to Auto, the printer processes print jobs from computers using either Windows or Macintosh operating systems When set to Off, the printer filters PostScript print jobs using the standard protocol.
Enable USB Port Off On*	Enable the standard USB port.

Menu item

Description

PCL SmartSwitch

Off
On*

Set the printer to switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.

Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

PS SmartSwitch

Off
On*

Set the printer to switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.

Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

Job Buffering

Off*
On

Temporarily store jobs on the printer hard disk before printing.

Note: This menu item appears only when a hard disk installed.

Mac Binary PS

On
Auto*
Off

Set the printer to process Macintosh binary PostScript print jobs.

Notes:

When set to On, the printer processes raw binary PostScript print jobs from computers using the Macintosh operating system.
When set to Auto, the printer processes print jobs from computers using either Windows or Macintosh operating systems
When set to Off, the printer filters PostScript print jobs using the standard protocol.

Enable USB Port

Off
On*

Enable the standard USB port.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Registration Register	Register the printer to the Google Cloud Print server.
Options Enable Google Cloud Print Off On*	Print directly from your Google account.
Options Enable Local Discovery Off On*	Allow the registered user and other users on the same subnet to send jobs to the printer locally.
Options Enable SSL Peer Verification Off On*	Verify authenticity of the peer certificate to connect to your Google account.
Options Always Print As Image Off* On	Set the printer to process PDF files as an image for faster printing.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
SSID	Specify the service set identifier (SSID) of the Wi-Fi network.
Set Preshared Key	Set the preshared key (PSK) to authenticate and validate users on a Wi-Fi connection.
Show PSK on Setup Page Off On*	Show the PSK on the Network Setup Page.
Group Owner IP Address	Specify the IP address of the group owner.
Auto-Accept Push Button Requests Off* On	Accept requests to connect to the network automatically. Note: Accepting clients automatically is not secured.