Network/Ports

Network Overview

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Active Adapter Auto* Standard Network Wireless	Specify the type of the network connection. Note: Wireless is available only in printers connected to a wireless network.
Network Status	Show the connectivity status of the printer network.
Display Network Status on Printer Off On*	Show the network status on the display.
Speed, Duplex	Show the speed of the currently active network card.
IPv4	Show the IPv4 address.
All IPv6 Addresses	Show all IPv6 addresses.
Reset Print Server	Reset all active network connections to the printer. Note: This setting removes all network configuration settings.
Network Job Timeout Off On* (90 seconds)	Set the time before the printer cancels a network print job.
Banner Page Off* On	Print a banner page.
Enable Network Connections Off On*	Enable the printer to connect to a network.
Enable LLDP Off* On	Enable Link Layer Discovery Protocol (LLDP) in the printer.

Menu item

Description

Active Adapter

Auto*

Standard Network

Wireless

Specify the type of the network connection.

Note: Wireless is available only in printers connected to a wireless network.

Network Status

Show the connectivity status of the printer network.

Display Network Status on Printer

Off

On*

Show the network status on the display.

Speed, Duplex

Show the speed of the currently active network card.

IPv4

Show the IPv4 address.

All IPv6 Addresses

Show all IPv6 addresses.

Reset Print Server

Reset all active network connections to the printer.

Note: This setting removes all network configuration settings.

Network Job Timeout

Off

On* (90 seconds)

Set the time before the printer cancels a network print job.

Banner Page

Off*

On

Print a banner page.

Enable Network Connections

Off

On*

Enable the printer to connect to a network.

Enable LLDP

Off*

On

Enable Link Layer Discovery Protocol (LLDP) in the printer.

Wireless

Note: This menu is available only in printers connected to a Wi-Fi network or printers that have a wireless network adapter.

Menu item	Description
Setup Using Mobile App	Configure the Wi-Fi connection using Lexmark Mobile Assistant.
Setup On Printer Panel Choose Network Add Wi-Fi Network Network Name Network Mode Infrastructure Wireless Security Mode Disabled* WEP WPA2/WPA - Personal WPA2 - Personal 802.1x - RADIUS	Configure the Wi-Fi connection using the control panel. Note: 802.1x - RADIUS can be configured only from the Embedded Web Server.
Wi-Fi Protected Setup WPS Auto Detect Off On* Start Push Button Method Start PIN Method	Establish a Wi-Fi network and enable network security. Notes: WPS Auto Detect appears only when the Wireless Security Mode is set to WEP. Start Push-Button Method connects the printer to a Wi-Fi network when buttons on both the printer and the access point (wireless router) are pressed within a given time. Start PIN Method connects the printer to a Wi-Fi network when a PIN on the printer is entered into the wireless settings of the access point.
Network Mode BSS Type Infrastructure*	Specify the network mode.
Enable Wi-Fi Direct On Off*	Enable Wi-Fi Direct-capable devices to connect directly to the printer.
Compatibility 802.11b/g/n (2.4GHz)* 802.11a/b/g/n/ac (2.4GHz/5GHz) 802.11a/n/ac (5GHz)	Specify the standard for the Wi-Fi network. Note: 802.11a/b/g/n/ac (2.4GHz/5GHz) and 802.11a/n/ac (5GHz) only appear when a Wi-Fi option is installed.
Wireless Security Mode Disabled* WEP WPA2/WPA-Personal WPA2-Personal 802.1x - RADIUS	Set the security mode for connecting the printer to Wi-Fi devices. Note: 802.1x - RADIUS can be configured only from the Embedded Web Server.
WEP Authentication Mode Auto* Open Shared	Set the type of Wireless Encryption Protocol (WEP) for the printer. Note: This menu item appears only when the Wireless Security Mode is set to WEP.
Set WEP Key	Specify a WEP password for secure Wi-Fi connection.
WPA2/WPA Personal AES	Enable Wi-Fi security through Wi-Fi Protected Access (WPA). Note: This menu item appears only when the Wireless Security Mode is set to WPA2/WPA-Personal.
Set Pre-Shared Key	Set the password for secure Wi-Fi connection.
WPA2-Personal AES	Enable Wi-Fi security through WPA2. Note: This menu item appears only when the Wireless Security Mode is set to WPA2-Personal.
802.1x Encryption Mode WPA+ WPA2*	Enable Wi-Fi security through 802.1x standard. Notes: This menu item appears only when the Wireless Security Mode is set to 802.1x - RADIUS. 802.1x - RADIUS can be configured only from the Embedded Web Server.
IPv4 Enable DHCP On* Off Set Static IP Address IP Address Netmask Gateway	Enable and configure IPv4 settings in the printer.
IPv6 Enable IPv6 On* Off Enable DHCPv6 On Off* Stateless Address Autoconfiguration On* Off DNS Server Address Manually Assigned IPv6 Address Manually Assigned IPv6 Router Address Prefix All IPv6 Addresses All IPv6 Router Addresses	Enable and configure IPv6 settings in the printer.
Network Address UAA LAA	View the network addresses.
PCL SmartSwitch Off On*	Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language. Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
PS SmartSwitch Off On*	Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language. Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
Job Buffering On Off*	Temporarily store print jobs in the printer hard disk before printing. Note: This menu item appears only when a hard disk is installed.
Mac Binary PS Auto* On Off	Set the printer to process Macintosh binary PostScript print jobs. Notes: On processes raw binary PostScript print jobs. Off filters print jobs using the standard protocol.

Menu item

Description

Setup Using Mobile App

Configure the Wi-Fi connection using Lexmark Mobile Assistant.

Setup On Printer Panel

Choose Network

Add Wi-Fi Network

Network Name

Network Mode

Infrastructure

Wireless Security Mode

Disabled*

WEP

WPA2/WPA - Personal

WPA2 - Personal

802.1x - RADIUS

Configure the Wi-Fi connection using the control panel.

Note: 802.1x - RADIUS can be configured only from the Embedded Web Server.

Wi-Fi Protected Setup

WPS Auto Detect

Off

On*

Start Push Button Method

Start PIN Method

Establish a Wi-Fi network and enable network security.

Notes:

WPS Auto Detect appears only when the Wireless Security Mode is set to WEP.
Start Push-Button Method connects the printer to a Wi-Fi network when buttons on both the printer and the access point (wireless router) are pressed within a given time.
Start PIN Method connects the printer to a Wi-Fi network when a PIN on the printer is entered into the wireless settings of the access point.

Network Mode

BSS Type

Infrastructure*

Specify the network mode.

Enable Wi-Fi Direct

On

Off*

Enable Wi-Fi Direct-capable devices to connect directly to the printer.

Compatibility

802.11b/g/n (2.4GHz)*

802.11a/b/g/n/ac (2.4GHz/5GHz)

802.11a/n/ac (5GHz)

Specify the standard for the Wi-Fi network.

Note: 802.11a/b/g/n/ac (2.4GHz/5GHz) and 802.11a/n/ac (5GHz) only appear when a Wi-Fi option is installed.

Wireless Security Mode

Disabled*

WEP

WPA2/WPA-Personal

WPA2-Personal

802.1x - RADIUS

Set the security mode for connecting the printer to Wi-Fi devices.

Note: 802.1x - RADIUS can be configured only from the Embedded Web Server.

WEP Authentication Mode

Auto*

Open

Shared

Set the type of Wireless Encryption Protocol (WEP) for the printer.

Note: This menu item appears only when the Wireless Security Mode is set to WEP.

Set WEP Key

Specify a WEP password for secure Wi-Fi connection.

WPA2/WPA Personal

AES

Enable Wi-Fi security through Wi-Fi Protected Access (WPA).

Note: This menu item appears only when the Wireless Security Mode is set to WPA2/WPA-Personal.

Set Pre-Shared Key

Set the password for secure Wi-Fi connection.

WPA2-Personal

AES

Enable Wi-Fi security through WPA2.

Note: This menu item appears only when the Wireless Security Mode is set to WPA2-Personal.

802.1x Encryption Mode

WPA+

WPA2*

Enable Wi-Fi security through 802.1x standard.

Notes:

This menu item appears only when the Wireless Security Mode is set to 802.1x - RADIUS.
802.1x - RADIUS can be configured only from the Embedded Web Server.

IPv4

Enable DHCP

On*

Off

Set Static IP Address

IP Address

Netmask

Gateway

Enable and configure IPv4 settings in the printer.

IPv6

Enable IPv6

On*

Off

Enable DHCPv6

On

Off*

Stateless Address Autoconfiguration

On*

Off

DNS Server Address

Manually Assigned IPv6 Address

Manually Assigned IPv6 Router

Address Prefix

All IPv6 Addresses

All IPv6 Router Addresses

Enable and configure IPv6 settings in the printer.

Network Address

UAA

LAA

View the network addresses.

PCL SmartSwitch

Off

On*

Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language.

Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

PS SmartSwitch

Off

On*

Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language.

Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

Job Buffering

On

Off*

Temporarily store print jobs in the printer hard disk before printing.

Note: This menu item appears only when a hard disk is installed.

Mac Binary PS

Auto*

On

Off

Set the printer to process Macintosh binary PostScript print jobs.

Notes:

On processes raw binary PostScript print jobs.
Off filters print jobs using the standard protocol.

Ethernet

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Network Speed	Show the speed of the active network adapter.
IPv4 Enable DHCP (On*) Set Static IP Address	Configure the IPv4 settings.
IPv6 Enable IPv6 (On) Enable DHCPv6 (Off) Stateless Address Autoconfiguration (On) DNS Server Address Manually Assigned IPv6 Address Manually Assigned IPv6 Router Address Prefix (64) All IPv6 Addresses All IPv6 Router Addresses	Configure the IPv6 settings.
Network Address UAA LAA	Specify the network address.
PCL SmartSwitch Off On*	Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language. Note: When this setting is disabled, the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
PS SmartSwitch Off On*	Set the printer to switch automatically to PostScript emulation when a print job requires it, regardless of the default printer language. Note: When this setting is disabled, the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
Job Buffering Off* On	Temporarily store jobs on the hard disk before printing. Note: This menu item appears only when a hard disk is installed.
Mac Binary PS Auto* On Off	Set the printer to process Macintosh binary PostScript print jobs. Notes: Auto processes print jobs from computers using either Windows or Macintosh operating systems. Off filters PostScript print jobs using the standard protocol.
Energy Efficient Ethernet On Off Auto*	Reduce power consumption when the printer does not receive data from the Ethernet network.

Menu item

Description

Network Speed

Show the speed of the active network adapter.

IPv4

Enable DHCP (On*)

Set Static IP Address

Configure the IPv4 settings.

IPv6

Enable IPv6 (On*)

Enable DHCPv6 (Off*)

Stateless Address Autoconfiguration (On*)

DNS Server Address

Manually Assigned IPv6 Address

Manually Assigned IPv6 Router

Address Prefix (64*)

All IPv6 Addresses

All IPv6 Router Addresses

Configure the IPv6 settings.

Network Address

UAA

LAA

Specify the network address.

PCL SmartSwitch

Off

On*

Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language.

Note: When this setting is disabled, the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

PS SmartSwitch

Off

On*

Set the printer to switch automatically to PostScript emulation when a print job requires it, regardless of the default printer language.

Note: When this setting is disabled, the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

Job Buffering

Off*

On

Temporarily store jobs on the hard disk before printing.

Note: This menu item appears only when a hard disk is installed.

Mac Binary PS

Auto*

On

Off

Set the printer to process Macintosh binary PostScript print jobs.

Notes:

Auto processes print jobs from computers using either Windows or Macintosh operating systems.
Off filters PostScript print jobs using the standard protocol.

Energy Efficient Ethernet

On

Off

Auto*

Reduce power consumption when the printer does not receive data from the Ethernet network.

TCP/IP

Note: This menu appears only in network printers or printers attached to print servers.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Set Hostname	Set the current TCP/IP host name.
Domain Name	Set the domain name.
Allow DHCP/BOOTP to update NTP server On* Off	Allow the DHCP and BOOTP clients to update the NTP settings of the printer.
Zero Configuration Name	Specify a service name for the zero configuration network.
Enable Auto IP Off* On	Assign an IP address automatically.
DNS Server Address	Specify the current Domain Name System (DNS) server address.
Backup DNS Address	Specify the backup DNS server addresses.
Backup DNS Address 2
Backup DNS Address 3
Domain Search Order	Specify a list of domain names to locate the printer and its resources that reside in different domains on the network.
Enable DDNS Off* On	Update the Dynamic DNS settings.
DDNS TTL	Specify the current DDNS settings.
Default TTL
DDNS Refresh Time
Enable mDNS Off On*	Update the multicast DNS settings.
WINS Server Address	Specify a server address for Windows Internet Name Service (WINS).
Enable BOOTP Off* On	Allow the BOOTP to assign a printer IP address.
Restricted Server List	Specify the IP addresses that are allowed to communicate with the printer over TCP/IP. Notes: Use a comma to separate each IP address. You can add up to 50 IP addresses.
Restricted Server List Options Block All Ports* Block Printing Only Block Printing and HTTP Only	Specify the access option for IP addresses that are not in the list.
MTU 256–1500 Ethernet (1500*)	Specify a maximum transmission unit (MTU) parameter for the TCP connections.
Raw Print Port 1–65535 (9100*)	Specify a raw port number for printers connected on a network.
Outbound Traffic Maximum Speed Off* On	Set the maximum transfer rate of the printer. Note: When enabled, the option for this setting is 100–1000000 Kilobits/second.
Enable TLSv1.0 Off On*	Enable the TLSv1.0 protocol.
Enable TLSv1.1 Off On*	Enable the TLSv1.1 protocol.
SSL Cipher List	Specify the cipher algorithms to use for the SSL or the TLS connections.

Menu item

Description

Set Hostname

Set the current TCP/IP host name.

Domain Name

Set the domain name.

Allow DHCP/BOOTP to update NTP server

On*

Off

Allow the DHCP and BOOTP clients to update the NTP settings of the printer.

Zero Configuration Name

Specify a service name for the zero configuration network.

Enable Auto IP

Off*

On

Assign an IP address automatically.

DNS Server Address

Specify the current Domain Name System (DNS) server address.

Backup DNS Address

Specify the backup DNS server addresses.

Backup DNS Address 2

Backup DNS Address 3

Domain Search Order

Specify a list of domain names to locate the printer and its resources that reside in different domains on the network.

Enable DDNS

Off*

On

Update the Dynamic DNS settings.

DDNS TTL

Specify the current DDNS settings.

Default TTL

DDNS Refresh Time

Enable mDNS

Off

On*

Update the multicast DNS settings.

WINS Server Address

Specify a server address for Windows Internet Name Service (WINS).

Enable BOOTP

Off*

On

Allow the BOOTP to assign a printer IP address.

Restricted Server List

Specify the IP addresses that are allowed to communicate with the printer over TCP/IP.

Notes:

Use a comma to separate each IP address.
You can add up to 50 IP addresses.

Restricted Server List Options

Block All Ports*

Block Printing Only

Block Printing and HTTP Only

Specify the access option for IP addresses that are not in the list.

MTU

256–1500 Ethernet (1500*)

Specify a maximum transmission unit (MTU) parameter for the TCP connections.

Raw Print Port

1–65535 (9100*)

Specify a raw port number for printers connected on a network.

Outbound Traffic Maximum Speed

Off*

On

Set the maximum transfer rate of the printer.

Note: When enabled, the option for this setting is 100–1000000 Kilobits/second.

Enable TLSv1.0

Off

On*

Enable the TLSv1.0 protocol.

Enable TLSv1.1

Off

On*

Enable the TLSv1.1 protocol.

SSL Cipher List

Specify the cipher algorithms to use for the SSL or the TLS connections.

SNMP

Note: This menu appears only in network printers or printers that are attached to print servers.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
SNMP Versions 1 and 2c Enabled Off On* Allow SNMP Set Off On* Enable PPM MIB Off On* SNMP Community	Configure Simple Network Management Protocol (SNMP) versions 1 and 2c to install print drivers and applications.
SNMP Version 3 Enabled Off On* Set Read/Write Credentials User Name Password Set Read-only Credentials User Name Password Authentication Hash MD5 SHA1* Minimum Authentication Level No Authentication, No Privacy Authentication, No Privacy Authentication, Privacy* Privacy Algorithm DES AES-128*	Configure SNMP version 3 to install and update the printer security.

Menu item

Description

SNMP Versions 1 and 2c

Enabled

Off

On*

Allow SNMP Set

Off

On*

Enable PPM MIB

Off

On*

SNMP Community

Configure Simple Network Management Protocol (SNMP) versions 1 and 2c to install print drivers and applications.

SNMP Version 3

Enabled

Off

On*

Set Read/Write Credentials

User Name

Password

Set Read-only Credentials

User Name

Password

Authentication Hash

MD5

SHA1*

Minimum Authentication Level

No Authentication, No Privacy

Authentication, No Privacy

Authentication, Privacy*

Privacy Algorithm

DES

AES-128*

Configure SNMP version 3 to install and update the printer security.

IPSec

Note: This menu appears only in network printers or printers that are attached to print servers.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Enable IPSec Off On*	Enable Internet Protocol Security (IPSec).
Base Configuration Default* Compatibility Secure	Set the IPSec base configuration.
DH (Diffie-Hellman) Group Proposal modp2048 (14)* modp3072 (15) modp4096 (16) modp6144 (17)	Set the IPSec base configuration. Note: This menu item appears only when Base Configuration is set to Compatibility.
Proposed Encryption Method 3DES AES*	Set the encryption method. Note: This menu item appears only when Base Configuration is set to Compatibility.
Proposed Authentication Method SHA1 SHA256* SHA512	Set the authentication method. Note: This menu item appears only when Base Configuration is set to Compatibility.
IKE SA Lifetime (Hours) 1 2 4 8 24*	Specify the IKE SA expiry period. Note: This menu item appears only when Base Configuration is set to Secure.
IPSec SA Lifetime (Hours) 1 2 4 8* 24	Specify the IPSec SA expiry period. Note: This menu item appears only when Base Configuration is set to Secure.
IPSec Device Certificate	Specify an IPSec certificate.
Pre-Shared Key Authenticated Connections Host [x]	Configure the authenticated connections of the printer.
Certificate Authenticated Connections Host [x] Address[/subnet]

Menu item

Description

Enable IPSec

Off

On*

Enable Internet Protocol Security (IPSec).

Base Configuration

Default*

Compatibility

Secure

Set the IPSec base configuration.

DH (Diffie-Hellman) Group Proposal

modp2048 (14)*

modp3072 (15)

modp4096 (16)

modp6144 (17)

Set the IPSec base configuration.

Note: This menu item appears only when Base Configuration is set to Compatibility.

Proposed Encryption Method

3DES

AES*

Set the encryption method.

Note: This menu item appears only when Base Configuration is set to Compatibility.

Proposed Authentication Method

SHA1

SHA256*

SHA512

Set the authentication method.

Note: This menu item appears only when Base Configuration is set to Compatibility.

IKE SA Lifetime (Hours)

1

2

4

8

24*

Specify the IKE SA expiry period.

Note: This menu item appears only when Base Configuration is set to Secure.

IPSec SA Lifetime (Hours)

1

2

4

8*

24

Specify the IPSec SA expiry period.

Note: This menu item appears only when Base Configuration is set to Secure.

IPSec Device Certificate

Specify an IPSec certificate.

Pre-Shared Key Authenticated Connections

Host [x]

Configure the authenticated connections of the printer.

Certificate Authenticated Connections

Host [x] Address[/subnet]

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Active Off* On	Let the printer join networks that require authentication before allowing access.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
LPD Timeout 0–65535 seconds (90*)	Set the time-out value to stop the Line Printer Daemon (LPD) server from waiting indefinitely for hung or invalid print jobs.
LPD Banner Page Off* On	Print a banner page for all LPD print jobs. Note: A banner page is the first page of a print job used as a separator of print jobs and to identify the originator of the print job request.
LPD Trailer Page Off* On	Print a trailer page for all LPD print jobs. Note: A trailer page is the last page of a print job.
LPD Carriage Return Conversion Off* On	Enable carriage return conversion. Note: Carriage return is a mechanism that commands the printer to move the position of the cursor to the first position on the same line.

HTTP/FTP Settings

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Enable HTTP Server Off On*	Access the Embedded Web Server to monitor and manage the printer.
Enable HTTPS Off On*	Enable Hypertext Transfer Protocol Secure (HTTPS) to encrypt data transferring to and from the print server.
Force HTTPS Connections On Off*	Force the printer to use HTTPS connections.
Enable FTP/TFTP Off On*	Send files using FTP/TFTP.
Local Domains	Specify domain names for HTTP and FTP servers.
HTTP Proxy IP Address	Configure the HTTP and FTP server settings.
FTP Proxy IP Address
HTTP Default IP Port
HTTPS Device Certificate
FTP Default IP Port
Timeout for HTTP/FTP Requests 1–299 (30*)	Specify the amount of time before the server connection stops.
Retries for HTTP/FTP Requests 1–299 (3*)	Set the number of retries to connect to the HTTP/FTP server.

Menu item

Description

Enable HTTP Server

Off

On*

Access the Embedded Web Server to monitor and manage the printer.

Enable HTTPS

Off

On*

Enable Hypertext Transfer Protocol Secure (HTTPS) to encrypt data transferring to and from the print server.

Force HTTPS Connections

On

Off*

Force the printer to use HTTPS connections.

Enable FTP/TFTP

Off

On*

Send files using FTP/TFTP.

Local Domains

Specify domain names for HTTP and FTP servers.

HTTP Proxy IP Address

Configure the HTTP and FTP server settings.

FTP Proxy IP Address

HTTP Default IP Port

HTTPS Device Certificate

FTP Default IP Port

Timeout for HTTP/FTP Requests

1–299 (30*)

Specify the amount of time before the server connection stops.

Retries for HTTP/FTP Requests

1–299 (3*)

Set the number of retries to connect to the HTTP/FTP server.

USB

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
PCL SmartSwitch Off On*	Set the printer to switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language. Note: When this setting is disabled, the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
PS SmartSwitch Off On*	Set the printer to switch to PostScript emulation when a print job received through a USB port requires it, regardless of the default printer language. Note: When this setting is disabled, the printer does not examine incoming data and uses the default printer language specified in the Setup menu.
Job Buffering Off* On	Temporarily store jobs on the hard disk before printing. Note: This menu item appears only when a hard disk is installed.
Mac Binary PS Auto* On Off	Set the printer to process Macintosh binary PostScript print jobs. Notes: Auto processes print jobs from computers using either Windows or Macintosh operating systems. Off filters PostScript print jobs using the standard protocol.
Enable USB Port Off On*	Enable the front USB drive port.

Menu item

Description

PCL SmartSwitch

Off

On*

Set the printer to switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.

Note: When this setting is disabled, the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

PS SmartSwitch

Off

On*

Set the printer to switch to PostScript emulation when a print job received through a USB port requires it, regardless of the default printer language.

Note: When this setting is disabled, the printer does not examine incoming data and uses the default printer language specified in the Setup menu.

Job Buffering

Off*

On

Temporarily store jobs on the hard disk before printing.

Note: This menu item appears only when a hard disk is installed.

Mac Binary PS

Auto*

On

Off

Set the printer to process Macintosh binary PostScript print jobs.

Notes:

Auto processes print jobs from computers using either Windows or Macintosh operating systems.
Off filters PostScript print jobs using the standard protocol.

Enable USB Port

Off

On*

Enable the front USB drive port.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Restrict external network access Off* On	Restrict access to network sites.
External network address	Specify the network addresses with restricted access.
E-mail address for notification	Specify an e-mail address to send a notification of logged events.
Ping frequency 1–300 (10*)	Specify the network query interval in seconds.
Subject	Specify the subject and message of the notification e-mail.
Message	Specify the subject and message of the notification e-mail.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
Registration Register	Register the printer to the Google Cloud Print server.
Options Enable Google Cloud Print Off On*	Print directly from your Google account.
Options Enable Local Discovery Off On*	Allow the registered user and other users on the same subnet to send jobs to the printer locally.
Options Enable SSL Peer Verification Off On*	Verify authenticity of the peer certificate to connect to your Google account.
Options Always Print As Image Off* On	Set the printer to process PDF files as an image for faster printing.

Menu item	Description
Note: An asterisk (*) next to a value indicates the factory default setting.
SSID	Specify the service set identifier (SSID) of the Wi-Fi network.
Preferred Channel Number Auto 1–11 (6*)	Show the PSK on the Network Setup Page.
Set PSK	Set the preshared key (PSK) to authenticate and validate users on a Wi-Fi connection.
Show PSK on Setup Page Off On*	Show the PSK on the Network Setup Page.
Group Owner IP Address	Specify the IP address of the group owner.
Auto-Accept Push Button Requests Off* On	Accept requests to connect to the network automatically. Note: Accepting clients automatically is not secure.