Preparing to set up the printer on an Ethernet network

To configure your printer to connect to an Ethernet network, organize the following information before you begin:

• A valid, unique IP address for the printer to use on the network

• The network gateway

• The network mask

• A nickname for the printer (optional)

  Note: A printer nickname can make it easier for you to identify your printer on the network. You can choose to use the default printer nickname, or assign a name that is easier for you to remember.

You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.

Preparing to set up the printer on a wireless network

Notes:

• Make sure your wireless network adapter is installed in your printer and working properly. For more information, see the instruction sheet that came with the wireless network adapter.
• Make sure your access point (wireless router) is turned on and is working properly.

Make sure you have the following information before setting up the printer on a wireless network:

• SSID—The SSID is also referred to as the network name.

• Wireless Mode (or Network Mode)—The mode is either infrastructure or ad hoc.

• Channel (for ad hoc networks)—The channel defaults to automatic for infrastructure networks.

  Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select.

• Security Method—There are four basic options for Security Method:

  • WEP key

    If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key.

  • WPA or WPA2 preshared key or passphrase

    WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network.

  • 802.1X–RADIUS

    If you are installing the printer on an 802.1X network, then you may need the following:

    • Authentication type

    • Inner authentication type

    • 802.1X user name and password

    • Certificates

  • No security

    If your wireless network does not use any type of security, then you will not have any security information.

    Note: We do not recommend using an unsecured wireless network.

Notes:

• If you do not know the SSID of the network that your computer is connected to, then launch the wireless utility of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point, or contact your system support person.
• To find the WPA/WPA2 preshared key or passphrase for the wireless network, see the documentation that came with the access point, see the Embedded Web Server associated with the access point, or consult your system support person.

Connecting the printer using the Wireless Setup Wizard

Before you begin, make sure that:

• A wireless network adapter is installed in the printer and is working properly. For more information, see the instruction sheet that came with the adapter.

• The Ethernet cable is disconnected from the printer.

• Active NIC is set to Auto. To set this to Auto, from the control panel, navigate to:

  > Settings > > Network/Ports > > Active NIC > > Auto >

1. From the control panel, navigate to:

   > Settings > > Network/Ports > > Network [x] > > Network [x] Setup > > Wireless > > Wireless Connection Setup >

2. Select a wireless connection setup.

   Use	To
   Search for networks	Show available wireless connections. Note: This menu item shows all broadcast secured or unsecured SSIDs.
   Enter a network name	Manually type the SSID.
   Wi-Fi Protected Setup	Connect the printer to a wireless network using Wi-Fi Protected Setup.

   
   

3. Follow the instructions on the printer display.

Connecting the printer to a wireless network using Wi-Fi Protected Setup

Before connecting the printer to a wireless network, make sure that:

• The access point (wireless router) is Wi-Fi Protected Setup (WPS) certified or WPS-compatible. For more information, see the documentation that came with your access point.

• A wireless network adapter installed in your printer is attached and working properly. For more information, see the instruction sheet that came with the wireless network adapter.

Using the Push Button Configuration method

1. From the printer control panel, navigate to:

   > Network/Ports > > Network [x] > > Network [x] Setup > > Wireless > > Wi-Fi Protected Setup > > Start Push Button Method >

2. Follow the instructions on the printer display.

Using the Personal Identification Number (PIN) method

1. From the printer control panel, navigate to:

   > Network/Ports > > Network [x] > > Network [x] Setup > > Wireless > > Wi-Fi Protected Setup > > Start PIN Method >

2. Copy the eight-digit WPS PIN.

3. Open a Web browser, and then type the IP address of your access point in the address field.

   Notes:

   • The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123.
   • If you are using a proxy server, then temporarily disable it to load the Web page correctly.

4. Access the WPS settings. For more information, see the documentation that came with your access point.

5. Enter the eight-digit PIN, and then save the setting.

Connecting the printer to a wireless network using Wi-Fi Protected Setup

Before connecting the printer to a wireless network, make sure that:

• The access point (wireless router) is Wi-Fi Protected Setup (WPS) certified or WPS-compatible. For more information, see the documentation that came with your access point.

• A wireless network adapter is installed on your printer and is working properly. For more information, see the instruction sheet that came with the adapter.

Using the Push Button Configuration Method

1. From the control panel, navigate to:

   > Settings > > Networks/Ports > > Network [x] > > Network [x] Setup > > Wireless > > Wireless Connection Setup > > Wi-Fi Protected Setup > > Start Push Button Method >

2. Follow the instructions on the printer display.

Using the Personal Identification Number (PIN) Method

1. From the control panel, navigate to:

   > Settings > > Networks/Ports > > Network [x] > > Network [x] Setup > > Wireless > > Wireless Connection Setup > > Wi-Fi Protected Setup > > Start PIN Method >

2. Copy the eight-digit WPS PIN.

3. Open a Web browser, and then type the IP address of your access point in the address field.

   Notes:

   • The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123.
   • If you are accessing a proxy server, then temporarily disable it to load the Web page correctly.

4. Access the WPS settings. For more information, see the documentation that came with your access point.

5. Enter the eight-digit PIN, and then save the setting.

Using the Wireless Setup Utility (Windows only)

1. Check if the printer software is already installed.

2. Use the search command on the Start menu to locate Printer Home.

3. Open Printer Home, and then click Settings > Wireless Setup Utility.

4. Follow the steps on the computer screen.

Using the Wireless Setup Assistant (Macintosh only)

The Wireless Setup Assistant lets you:

• Configure the printer to join an existing wireless network.

• Add a printer to an existing ad hoc network.

• Change the wireless settings after installation.

• Install the printer on additional network computers.

Installing the Wireless Setup Assistant

1. Go to the Lexmark support Web site at http://support.lexmark.com.

2. Download the latest Wireless Setup Assistant application.

3. Double-click the downloaded software installer package.

4. Follow the instructions on the computer screen.

Launching the Wireless Setup Assistant

Notes:

• Make sure the printer is turned on.
• Make sure a wireless network adapter is installed in your printer and is working properly.

1. From the Finder, navigate to:

   Applications > select your printer folder

2. Double-click Wireless Setup Assistant, and then follow the instructions on the computer screen.

Note: If you encounter problems while running the application, then click .