From LMC, click the Services tab.
From the Services section, select Email.
From the Tasks section, select Parameters.
Type the e-mail server host name or IP address.
Type the user name and password used to log in to your SMTP server.
Enter the e-mail server connection timeout in seconds. The default value is .
Enter the e-mail server I/O timeout in seconds.
Click Apply.
To improve reliability during device discovery, configure the timeout periods between communication retries.
From LMC, click the Services tab.
From the Services section, select NPA.
From the Tasks section, select Parameters.
In the NPANT Timeout field, enter a timeout period in milliseconds for each retry in sequence, separating each by a space. The default values are and .
In the Unsecure Port field, enter the port number used for NPA on your network. The default value is .
Click Apply.
From LMC, click the Device Groups tab.
From the Device Groups section, select a device group.
From the Tasks section, select SNMP, and then clear Use Global.
In the Port field, enter the port number used for SNMP on your network. The default value is .
In the Timeouts/Retries field, enter a timeout period in milliseconds for each retry in sequence, separating each by a space.
Do either of the following:
Configure SNMP version 3.
Select SNMP v3.
Configure the SNMPv3 minimum authentication level.
In the SNMPv3 Read/Write User field, type the read and write user name.
In the SNMPv3 Read/Write Password field, type the read and write user name.
In the SNMPv3 Read Only User field, type the read user name.
In the SNMPv3 Read Only Password field, type the read password.
Configure the following:
SNMPv3 Authentication Hash
SNMPv3 Privacy Algorithm
Configure SNMP versions 1 and 2.
In the Write Community Name field, type the write community string for printers on your network.
In the Read Community Name field, type the read community string for printers on your network.
Clear SNMP v3.
Click Apply.
Do either of the following:
Using the Device Groups tab
From LMC, click the Device Groups tab.
From the Device Groups section, select a device group.
From the Tasks section, select SNMP, and then select Use Global.
Click Apply.
From LMC, click the Services tab.
From the Services section, select SNMP.
From the Tasks section, select Parameters.
In the Port field, enter the port number used for SNMP on your network. The default value is .
In the Timeouts/Retries field, enter a timeout period in milliseconds for each retry in sequence, separating each by a space.
Do either of the following:
Configure SNMP version 3.
Select SNMP v3.
Configure the SNMPv3 minimum authentication level.
In the SNMPv3 Read/Write User field, type the read and write user name.
In the SNMPv3 Read/Write Password field, type the read and write user name.
In the SNMPv3 Read Only User field, type the read user name.
In the SNMPv3 Read Only Password field, type the read password.
Configure the following:
SNMPv3 Authentication Hash
SNMPv3 Privacy Algorithm
Configure SNMP versions 1 and 2.
In the Write Community Name field, type the write community string for printers on your network.
In the Read Community Name field, type the read community string for printers on your network.
Clear SNMP v3.
Click Apply.
From Lexmark Management Console, click the Device Groups tab.
From the Device Groups section, select a device group.
From the Tasks section, select SNMP, and then clear Use Global.
Select the authentication type for the printer.
Type the authentication value for Password or PIN, or the LDAP setup name for LDAP or LDAP+GSSAPI.
Click Apply.
Do either of the following:
Using the Device Groups tab
From Lexmark Management Console, click the Device Groups tab.
From the Device Groups section, select a device group.
From the Tasks section, select SNMP, and then select Use Global.
Click Apply.
Using the Services tab
From Lexmark Management Console, click the Services tab.
From the Services section, select DeviceSecurity.
From the Tasks section, select Parameters.
Select the authentication type for the printer.
Type the authentication value for Password or PIN, or the LDAP setup name for LDAP or LDAP+GSSAPI.
Click Apply.