Safety information
Connect the power cord directly to an appropriately rated and
properly grounded electrical outlet that is near the product and easily
accessible.
| CAUTION—POTENTIAL INJURY: Do not use this product with extension cords, multioutlet
power strips, multioutlet extenders, or other types of surge or UPS
devices. The power rating capacity of these types of accessories
can be easily overloaded by a laser printer and may result in poor
printer performance, property damage, or potential fire. |
Do not place or use this product near water or wet locations.
| CAUTION—POTENTIAL INJURY: This product uses a laser. Use of controls
or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure. |
This product uses a printing process that heats the print media,
and the heat may cause the media to release emissions. You must understand
the section in your operating instructions that discusses the guidelines
for selecting print media to avoid the possibility of harmful emissions.
| CAUTION—POTENTIAL INJURY: The lithium battery in this product is not
intended to be replaced. There is a danger of explosion if a lithium
battery is incorrectly replaced. Do not recharge, disassemble, or
incinerate a lithium battery. Discard used lithium batteries according
to the manufacturer's instructions and local regulations. |
| CAUTION—HOT SURFACE: The inside of the printer might be hot.
To reduce the risk of injury from a hot component, allow the surface
to cool before touching it. |
| CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability,
load each tray separately. Keep all other trays closed until needed. |
| CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg
(40 lb) and requires two or more trained personnel to lift it safely. |
| CAUTION—POTENTIAL INJURY: Before moving the printer, follow these guidelines to avoid
personal injury or printer damage: |
Turn off the printer, and then unplug the power cord
from the electrical outlet.
Disconnect all cords and cables from the printer.
If the printer does not have a caster base but is
configured with optional trays, then remove the trays.
Use the handholds located on both sides of the printer
to lift it.
Make sure your fingers are not under the printer
when you set it down.
Make sure there is adequate clearance around the
printer.
Use only the power cord provided with this product
or the manufacturer's authorized replacement.
| CAUTION—SHOCK HAZARD: If you are accessing the controller board
or installing optional hardware or memory devices sometime after setting
up the printer, then turn the printer off, and unplug the power cord
from the electrical outlet before continuing. If you have any other
devices attached to the printer, then turn them off as well, and unplug
any cables going into the printer. |
| CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock
when cleaning the exterior of the printer, unplug the power cord from
the electrical outlet and disconnect all cables from the printer before
proceeding. |
| CAUTION—SHOCK HAZARD: Make sure that all external connections
(such as Ethernet and telephone system connections) are properly installed
in their marked plug-in ports. |
This product is designed, tested, and approved to meet strict
global safety standards with the use of specific manufacturer's components.
The safety features of some parts may not always be obvious. The manufacturer
is not responsible for the use of other replacement parts.
This product produces ozone during normal operation, and is
equipped with a filter designed to limit ozone concentrations to levels
well below the recommended exposure limits. To avoid high ozone concentration
levels during extensive usage, install this product in a well-ventilated
area and replace the ozone and exhaust filters as indicated in the
product maintenance instructions.
| CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place
heavy objects on the power cord. Do not subject the power cord to
abrasion or stress. Do not pinch the power cord between objects such
as furniture and walls. If any of these things happen, a risk of fire
or electrical shock results. Inspect the power cord regularly for
signs of such problems. Remove the power cord from the electrical
outlet before inspecting it. |
Refer service or repairs, other than those described in the
user documentation, to a service representative.
| CAUTION—SHOCK HAZARD: Do not set up this product or make any
electrical or cabling connections, such as a power cord, a fax feature
or USB cable, during a lightning storm. |
| CAUTION—TIPPING HAZARD: Floor-mounted configurations
require additional furniture for stability. You must use either a
printer stand or printer base if you are using multiple input options.
If you purchased a printer with a similar configuration, then you
may need additional furniture. For more information, see www.lexmark.com/multifunctionprinters. |