Use letterhead designed specifically for laser/LED printers.
Print samples on the letterhead being considered for use before buying large quantities.
Before loading letterhead, flex the sheets to prevent them from sticking together.
Page orientation is important when printing on letterhead.
Source | Print side | Paper orientation |
---|---|---|
Note: Check with the manufacturer or vendor to determine whether the chosen preprinted letterhead is acceptable for laser/LED printers. | ||
Standard and optional trays (simplex printing) | Preprinted letterhead design is placed faceup. | When feeding short edge, the top edge of the sheet with the logo is placed at the right side of the tray. When feeding long-edge, the letter head should go to the rear of the printer. |
Standard and optional trays (duplex printing) | Preprinted letterhead design is placed facedown. | The top edge of the sheet with the logo is placed at the right side of the tray. |
Multipurpose feeder (simplex printing) | Preprinted letterhead design is placed facedown. | The top edge of the sheet with the logo should enter the multipurpose feeder first. |
Multipurpose feeder (duplex printing) | Preprinted letterhead design is placed faceup. | The top edge of the sheet with the logo should enter the multipurpose feeder last. |
Print samples on the transparencies being considered for use before buying large quantities.
Feed transparencies from the standard tray or from the multipurpose feeder.
From the Paper menu, set the Paper Type to Transparency.
Use transparencies designed specifically for laser/LED printers. Transparencies must be able to withstand temperatures of 230°C (446°F) without melting, discoloring, offsetting, or releasing hazardous emissions.
To prevent print quality problems, avoid getting fingerprints on the transparencies.
Before loading transparencies, flex the stack to prevent sheets from sticking together.
We recommend Lexmark transparencies. For ordering information, see the Lexmark Web site at www.lexmark.com.
Print samples on the envelopes being considered for use before buying large quantities.
Use envelopes designed specifically for laser/LED printers. Check with the manufacturer or vendor to ensure that the envelopes can withstand temperatures up to 220°C (446°F) without sealing, wrinkling, curling excessively, or releasing hazardous emissions.
For best performance, use envelopes made from 90 g/m2 (24 lb bond) paper or 25% cotton. All-cotton envelopes must not exceed 70 g/m2 (20 lb bond) weight.
Use only new envelopes from undamaged packages.
To optimize performance and minimize jams, do not use envelopes that:
Have excessive curl or twist
Are stuck together or damaged in any way
Have windows, holes, perforations, cutouts, or embossing
Have metal clasps, string ties, or folding bars
Have an interlocking design
Have postage stamps attached
Have any exposed adhesive when the flap is in the sealed or closed position
Have bent corners
Have rough, cockle, or laid finishes
Adjust the width guides to fit the width of the envelopes.
Note: A combination of high humidity (over 60%) and the high printing temperature may wrinkle or seal envelopes. |
Notes:
For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on the Lexmark Web site at http://support.lexmark.com.
When printing on labels:
Use labels designed specifically for laser/LED printers. Check with the manufacturer or vendor to verify that:
The labels can withstand temperatures up to 210°C (410°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions.
Note: Labels can be printed at a higher fusing temperature up to 220°C (428°F) if Label Weight is set to Heavy. Select this setting using the Embedded Web Server, or from the printer control panel Paper menu. |
Label adhesives, face sheet (printable stock), and topcoats can withstand up to 25 psi (172 kPa) pressure without delaminating, oozing around the edges, or releasing hazardous fumes.
Do not use labels with slick backing material.
Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge warranties.
Do not use labels with exposed adhesive.
Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die-cuts of the label.
Be sure adhesive backing does not reach to the sheet edge. Zone coating of the adhesive at least 1 mm (0.04 in.) away from edges is recommended. Adhesive material contaminates the printer and could void the warranty.
If zone coating of the adhesive is not possible, then remove a 1.6 mm (0.06 in.) strip on the leading and driver edge, and use a non-oozing adhesive.
Portrait orientation works best, especially when printing bar codes.
Card stock is heavy, single-ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly impact print quality. Print samples on the card stock being considered for use before buying large quantities.
From the Paper menu, set the Paper Type to Card Stock.
Select the appropriate Paper Texture setting.
Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or other paper handling problems.
Check with the manufacturer or vendor to ensure the card stock can withstand temperatures up to 220°C (446°F) without releasing hazardous emissions.
Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting introduces semi-liquid and volatile components into the printer.
Use grain short card stock when possible.