Cartridge low [88.xy]

You may need to order a replacement toner cartridge. If necessary, touch Continue on the printer control panel to clear the message and continue printing.

Cartridge nearly low [88.xy]

If necessary, touch Continue on the printer control panel to clear the message and continue printing.

Cartridge very low [88.xy]

You may need to replace the toner cartridge very soon. For more information, see Replacing the toner cartridge .

If necessary, touch Continue on the control panel to clear the message and continue printing.

Change [paper source] to [custom string] load [orientation]

Try one or more of the following:

• Load the correct size and type of paper in the tray, specify the paper size and type in the Paper menu on the control panel, and then touch Finished changing paper .

• Touch Use current [paper source] to use the available paper size and type in the tray.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the print job.

Change [paper source] to [custom type name] load [orientation]

Try one or more of the following:

• Load the correct size and type of paper in the tray or feeder, specify the paper size and type in the Paper menu on the printer control panel, and then touch Finished changing paper .

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the print job.

Change [paper source] to [paper size] load [orientation]

Try one or more of the following:

• Load the correct size and type of paper in the tray or feeder, specify the size and type of paper in the Paper menu on the control panel, and then touch Finished changing paper .

• Touch Use current [paper source] to use the available size and type of paper in the current tray or feeder.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the print job.

Change [paper source] to [paper type] [paper size] load [orientation]

Try one or more of the following:

• Load the correct size and type of paper in the tray or feeder, specify the paper size and type in the Paper menu on the control panel, and then touch Finished changing paper .

• Touch Use current [paper source] to use the available paper size and type in the tray.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the print job.

Close door [x]

Close the specified door.

Complex page, some data may not have printed [39]

Try one or more of the following:

• From the control panel, touch Continue to clear the message and continue printing.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the print job.

• Install additional printer memory.

Configuration change, some held jobs were not restored [57]

Held jobs are invalidated because of the following possible changes in the printer:

• The printer firmware has been updated.

• The tray for the print job has been removed.

• The print job is sent from a flash drive that is no longer attached to the USB port.

• The printer hard disk contains print jobs that were stored when the hard disk was installed in a different printer model.

From the printer control panel, touch Continue to clear the message.

Defective flash detected [51]

Try one or more of the following:

• Replace the defective flash memory card.

• From the printer control panel, touch Continue to ignore the message and continue printing.

• Cancel the current print job.

Disk full [62]

Try one or more of the following:

• From the control panel, touch Continue to clear the message and continue printing.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Delete fonts, macros, and other data stored in the printer hard disk.

• Install a hard disk with larger capacity.

Disk must be formatted for use in this device

From the printer control panel, touch Format disk to format the printer hard disk and clear the message.

Disk near full. Securely clearing disk space.

Try one or more of the following:

• Touch Continue to clear the message and continue printing.

• Delete fonts, macros, and other data stored on the printer hard disk.

• Install a hard disk with higher capacity.

Empty the hole punch box

Try one or more of the following:

• Empty the hole punch box.

• Select Continue on the printer control panel to clear the message and continue printing.

• Cancel the print job.

Error reading USB drive. Remove USB.

An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.

Error reading USB hub. Remove hub.

An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.

Incorrect paper size, open [paper source] [34]

Try one or more of the following:

• Load the correct paper size and type in the tray or feeder, and then specify the paper size and type in the Paper menu on the control panel.

• Make sure that the correct paper size and type are specified in Print Properties or the Print dialog settings.

• Check the length and width guides and make sure that the paper is loaded properly in the tray or feeder.

• From the control panel, touch Continue to clear the message and then print using a different tray.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the print job.

Insert hole punch box

Insert the hole punch box into the finisher, and then touch Continue to clear the message.

Insert Tray [x]

Try one or more of the following:

• Insert the specified tray into the printer.

• Cancel the print job.

• Reset the active bin for a linked set of bins by selecting Reset active bin on the printer control panel.

Insufficient memory for Flash Memory Defragment operation [37]

Try one or more of the following:

• From the printer control panel, touch Continue to stop the defragmentation and continue printing.

• Delete fonts, macros, and other data in the printer memory.

• Install additional printer memory.

Insufficient memory to collate job [37]

Try one or more of the following:

• From the printer control panel, touch Continue to print the part of the job already stored and begin collating the rest of the print job.

• Cancel the current print job.

Insufficient memory to support Resource Save feature [35]

Install additional printer memory or touch Continue to disable Resource Save, clear the message, and continue printing.

Insufficient memory, some Held Jobs were deleted [37]

From the printer control panel, touch Continue to clear the message.

Insufficient memory, some held jobs will not be restored [37]

Try one or more of the following:

• From the printer control panel, touch Continue to clear the message.

• Delete other held jobs to free up additional printer memory.

Insufficient space between paper stacks in Tray 3

Move the paper stacks apart, and then touch Continue on the control panel to clear the message and continue printing.

Load [paper source] with [custom string] [paper orientation]

Try one or more of the following:

• Load the tray or feeder with the correct size and type of paper, and then touch Finished loading paper on the control panel.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the current job.

Load [paper source] with [custom type name] [paper orientation]

Try one or more of the following:

• Load the tray or feeder with the correct size and type of paper, and then touch Finished loading paper on the control panel.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the print job.

Load [paper source] with [paper size] [paper orientation]

Try one or more of the following:

• Load the tray or feeder with the correct size of paper, and then touch Finished loading paper on the control panel.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the current job.

Load [paper source] with [paper type] [paper size] [paper orientation]

Try one or more of the following:

• Load the specified tray or feeder with the correct size and type of paper, and then touch Finished loading paper on the control panel.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Cancel the current job.

Load Multipurpose Feeder with [custom string] [paper orientation]

Try one or more of the following:

• Load the feeder with the correct size and type of paper.

• From the control panel, touch one of the following:

  • Prompt each page, paper loaded or Do not prompt, paper loaded —To clear the message and continue printing.

  • Automatically select paper —To use the paper loaded in the tray.

  • Reset active bin —To reset the active bin for a linked set of bins.

• Cancel the print job.

Load Multipurpose Feeder with [custom type name] [paper orientation]

Try one or more of the following:

• Load the feeder with the correct size and type of paper.

• From the control panel, touch one of the following:

  • Prompt each page, paper loaded or Do not prompt, paper loaded —To clear the message and continue printing.

  • Automatically select paper —To use the paper loaded in the tray.

  • Reset active bin —To reset the active bin for a linked set of bins.

• Cancel the print job.

Load Multipurpose Feeder with [paper size] [paper orientation]

Try one or more of the following:

• Load the feeder with the correct size of paper.

• From the control panel, touch one of the following:

  • Prompt each page, paper loaded or Do not prompt, paper loaded —To clear the message and continue printing.

  • Automatically select paper —To use the paper loaded in the tray.

  • Reset active bin —To reset the active bin for a linked set of bins.

• Cancel the print job.

Load Multipurpose Feeder with [paper type] [paper size] [paper orientation]

Try one or more of the following:

• Load the feeder with the correct size and type of paper.

• From the control panel, touch one of the following:

  • Prompt each page, paper loaded or Do not prompt, paper loaded —To clear the message and continue printing.

  • Automatically select paper —To use the paper loaded in the tray.

  • Reset active bin —To reset the active bin for a linked set of bins.

• Cancel the print job.

Load staples

Try one or more of the following:

• Replace or insert the staple cartridge in the finisher.

  For instructions on inserting or replacing a staple cartridge in the finisher, touch More information on the printer control panel.

• From the printer control panel, touch Continue to clear the message and continue printing.

• From the printer control panel, touch Cancel job to cancel the print job.

Load staples [G11, G12]

Try one or more of the following:

• Replace or insert the staple cartridge into the finisher.

  For instructions on replacing or inserting the staple cartridge into the finisher, touch More information on the control panel.

• From the control panel, touch Continue to clear the message and continue printing.

• Cancel the print job.

[x] maintenance kit very low [80.xy]

You may need to replace the maintenance kit very soon. For more information, go to the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.

If necessary, touch Continue to clear the message and continue printing.

Memory full [38]

Try one or more of the following:

• From the control panel, touch Cancel job to clear the message.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Install additional printer memory.

Network [x] software error [54]

Try one or more of the following:

• From the printer control panel, touch Continue to continue printing.

• Turn off the printer, wait for about 10 seconds, and then turn the printer back on.

• Update the network firmware in the printer or print server. For more information, visit the Lexmark support Web site at http://support.lexmark.com .

Not enough free space in flash memory for resources [52]

Try one or more of the following:

• From the control panel, touch Continue to clear the message and continue printing.

• Touch Reset active bin to reset the active bin for a linked set of bins.

• Delete fonts, macros, and other data stored in the flash memory.

• Install a flash memory card with larger capacity.

Note:  Downloaded fonts and macros not previously stored in the flash memory are deleted.

Open door H and remove paper from beneath area H10

Remove the paper from the specified area.

Paper changes needed

Try one or more of the following:

• Touch Use current supplies to clear the message and continue printing.

• Cancel the current print job.

Parallel port [x] disabled [56]

Try one or more of the following:

• From the printer control panel, touch Continue to clear the message.

• Enable the parallel port. From the printer control panel, navigate to:

  Network/Ports > Parallel [x] > Parallel Buffer > Auto

Note:  The printer discards any data received through the parallel port.

Photoconductor low [84.xy]

You may need to order a replacement photoconductor. If necessary, select Continue on the control panel to clear the message and continue printing.

Photoconductor very low [84.xy]

You may need to replace the photoconductor unit very soon. For more information, see Replacing a photoconductor unit .

If necessary, touch Continue on the control panel to clear the message and continue printing.

Printer had to restart. Last job may be incomplete.

From the printer control panel, touch Continue to clear the message and continue printing.

For more information, visit http://support.lexmark.com or contact customer support.

Reinstall missing or unresponsive cartridge [31.xy]

Try one or more of the following:

• Check if the toner cartridge is missing. If missing, install the toner cartridge.

  For information on installing the cartridge, see the “Replacing supplies” section of the User’s Guide .

• If the toner cartridge is installed, then remove the unresponsive toner cartridge, and then reinstall it.

  Note:  If the message appears after reinstalling the supply, then the cartridge is defective. Replace the toner cartridge.

Reinstall missing or unresponsive photoconductor [31.xy]

Try one or more of the following:

• If the photoconductor unit is missing, then install it. For more information, see Replacing a photoconductor unit .

• If the photoconductor unit is installed, then remove and then reinstall it.

  Note:  If the message appears after reinstalling the supply, then replace the defective photoconductor unit.

Remove defective disk [61]

Remove and replace the defective printer hard disk.

Remove packaging material, [area name]

Remove any remaining packaging material from the specified location.

Remove packaging material, open door C, remove metal clips

Open door C, and then remove any remaining packaging material.

Remove paper from all bins

Remove the paper from all of the bins. The printer automatically senses paper removal and resumes printing.

If removing the paper does not clear the message, then touch Continue .

Remove paper from bin [x]

Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.

If removing the paper does not clear the message, then touch Continue .

Remove paper from [linked set bin name]

Remove paper from the specified bin. The printer automatically detects paper removal and resumes printing.

If removing the paper does not clear the message, then touch Continue .

Remove paper from standard output bin

Remove the paper stack from the standard bin.

Replace cartridge, 0 estimated pages remain [88.xy]

Replace the toner cartridge to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide .

Replace cartridge, printer region mismatch [42.xy]

Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:

Notes:

• The x and y values represent . xy in the code that appears on the printer control panel.
• The x and y values must match for printing to continue.

Replace [x] maintenance kit, 0 estimated pages remain [80.xy]

The printer is scheduled for maintenance. For more information, go to the Lexmark support Web site at http://support.lexmark.com or contact your service representative, and then report the message.

Replace missing photoconductor [31.xy]

Install the missing photoconductor unit to clear the message. For more information, see Replacing a photoconductor unit .

Replace missing waste toner bottle [82.xy]

Install the missing waste toner bottle to clear the message. For more information, see the instruction sheet that came with the supply.

Replace missing cartridge [31.xy]

Install the missing cartridge to clear the message. For more information, see Replacing the toner cartridge .

Replace paper pick rollers in [paper source], use parts and instructions in tray 1 or tray 2 compartment [80]

Try one or more of the following:

• Replace the pick rollers, and then touch Rollers replaced on the control panel to clear the message and continue printing.

• Touch Replace later (jams may persist) to ignore the message and continue printing.

Replace photoconductor, 0 pages remain [84.xy]

Replace the photoconductor unit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see Replacing a photoconductor unit .

Replace unsupported cartridge [32.xy]

Remove the toner cartridge, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide .

Replace unsupported photoconductor [32.xy]

Remove the photoconductor unit, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see Replacing a photoconductor unit .

Replace waste toner bottle [82.xy]

Replace the waste toner bottle to clear the message.

Restore held jobs?

Try one or more of the following:

• From the printer control panel, touch Restore to restore all held jobs stored in the printer hard disk.

• From the printer control panel, touch Do not restore if you do not want to restore any of the print jobs.

Serial port [x] disabled [56]

Try one or more of the following:

• From the printer control panel, touch Continue to clear the message.

  The printer discards any data received through the specified serial port.

• Make sure Serial Buffer is not set to Disabled.

• From the printer control panel, set Serial Buffer to Auto in the Serial [x] menu.

Some held jobs were not restored

From the printer control panel, touch Continue to delete the indicated job.

SMTP server not set up. Contact system administrator.

From the printer control panel, touch Continue to clear the message.

Standard network software error [54]

Try one or more of the following:

• From the printer control panel, touch Continue to continue printing.

• Turn off the printer, and then turn it back on.

• Update the network firmware in the printer or print server. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.

Standard USB port disabled [56]

Try one or more of the following:

• From the printer control panel, touch Continue to clear the message.

• Enable the USB port. From the printer control panel, navigate to:

  Network/Ports > USB Buffer > Auto

Supply needed to complete job

Do either of the following:

• Install the missing supply to complete the job.

• Cancel the current job.

The device is operating in Safe Mode. Some print options may be disabled or provide unexpected results.

Touch Continue on the control panel to clear the message and continue printing.

Too many flash options installed [58]

Try one or more of the following:

• Touch Continue on the control panel to continue printing.

• Remove the extra flash memory:

  1. Turn off the printer.

  2. Unplug the power cord from the electrical outlet.

  3. Remove the extra flash memory.

  4. Connect the power cord to a properly grounded electrical outlet.

  5. Turn the printer back on.

Too many trays attached [58]

1. Turn off the printer.

2. Unplug the power cord from the electrical outlet.

3. Remove the extra trays.

4. Connect the power cord to a properly grounded electrical outlet.

5. Turn the printer back on.

Tray [x] paper size unsupported

Replace with a supported paper size.

Unformatted flash detected [53]

Try one or more of the following:

• From the printer control panel, touch Continue to stop the defragmentation and continue printing.

• Format the flash memory.

  Note:  If the error message remains, then the flash memory may be defective and needs to be replaced.

Unsupported disk

Remove the unsupported printer hard disk, and then insert a supported one.

Unsupported option in slot [x] [55]

1. Turn off the printer.

2. Unplug the power cord from the electrical outlet.

3. Remove the unsupported option card from the printer controller board, and then replace it with a supported card.

4. Connect the power cord to a properly grounded electrical outlet.

5. Turn the printer back on.

Waste toner bottle nearly full [82.xy]

You may need to order a waste toner bottle. If necessary, touch Continue on the printer control panel to clear the message and continue printing.

Weblink server not set up. Contact system administrator.

From the printer control panel, touch Continue to clear the message.